[implemented] ECoS 4.1 PT feature

Moderator: Moderators

Re: ECoS 4.1 feature

Postby hclaassens » 13.12.2015, 10:39

smitt48 wrote:Hi Rob,

Lots of people (me included) like a screenshot.

Tom


Hi Tom,

Sorry for my delayed reaction.

I must agree with Rob that screenshots for the Ecos programming do not add additional info. They look the same as for other command stations.
What I think would be addition is to write that POM is NOT supported (for now).
Also the "controllers-en" page should reflect that PT-programming is possible for the Ecos starting with firmware version 4.1.0.

Hans
hclaassens
 

Re: [implemented] ECoS 4.1 PT feature

Postby hclaassens » 13.12.2015, 11:54

Hi Rob,

In addition to previous messages, I think I've found something strange.
In the programmning tab I've selected the V-curve.
The CV's 67-94 are read correctly.
The a popup window is shown with the sliders on it, but the other popup window "Reading CV" stays on the screen.
I think this is confusing. Is thsi also the case with other command stations then the Ecos?

What makes it even worse is the fact that is stays on the screen when you're writing a modified speed curve.

I've added a screen shot.

regards,
Hans
You do not have the required permissions to view the files attached to this post.
hclaassens
 

Re: [implemented] ECoS 4.1 PT feature

Postby rjversluis » 13.12.2015, 12:15

Hi Hans,

I just fixed it.
Best Regards, Rob.
:!: PS: Do not forget to attach the usual files.
:!: PS: Nicht vergessen die übliche Dateien an zu hängen.
[ macOS - Linux] - [ N: CBus - CAN-GCA ] - [ 0: RocNetNode - GCA-Pi ]
rjversluis
Site Admin
 

Re: [implemented] ECoS 4.1 PT feature

Postby hclaassens » 13.12.2015, 13:30

rjversluis wrote:Hi Hans,

I just fixed it.


Rob,

I'm using revision 10297, but it is NOT fixed.

Hans
hclaassens
 

Re: [implemented] ECoS 4.1 PT feature

Postby rjversluis » 13.12.2015, 13:39

Hans,

how to reproduce?
Best Regards, Rob.
:!: PS: Do not forget to attach the usual files.
:!: PS: Nicht vergessen die übliche Dateien an zu hängen.
[ macOS - Linux] - [ N: CBus - CAN-GCA ] - [ 0: RocNetNode - GCA-Pi ]
rjversluis
Site Admin
 

Re: [implemented] ECoS 4.1 PT feature

Postby hclaassens » 13.12.2015, 14:08

rjversluis wrote:Hans,

how to reproduce?


Reproduce:

Choose loc panel, a loco and programming tab
button "v curve", confirm read and wait until the sliders are shown.
Then the Get CV popup is also shown.
Using Linux mint 17.2, 64 bit


Hans
hclaassens
 

Re: [implemented] ECoS 4.1 PT feature

Postby rjversluis » 13.12.2015, 15:58

I disabled the wxProgress dialog because the event handling is broken since wx3.
The dialog was and is a PITA.
I resigned it to use it in RocPro because of known problems
Best Regards, Rob.
:!: PS: Do not forget to attach the usual files.
:!: PS: Nicht vergessen die übliche Dateien an zu hängen.
[ macOS - Linux] - [ N: CBus - CAN-GCA ] - [ 0: RocNetNode - GCA-Pi ]
rjversluis
Site Admin
 

Previous

Return to ECoS - Marklin CS1

cron