DDX-Blacklist: Tams WD-34

Moderator: Moderators

DDX-Blacklist: Tams WD-34

Postby mbre » 09.04.2011, 20:22

Ich habe eventuell folgende Ergänzung für die Blacklist:
Ich verwende DDX mit Direktanschluss an Roco-Booster.

Der Tams Magnetartikeldekoder WD-34 reagiert bei mir überhaupt nicht.
Auch ein Versuch mit DDW-Server brachte keinen Erfolg.
Mit der Multimaus gibt es kein Problem den Dekoder anzusteuern.

Den Tams Lokdekoder LD-32 kann ich entgegen der Warnung in der Liste problemlos beschreiben aber nicht lesen.

Hat jemand andere Erfahrungen gemacht?
Last edited by mbre on 12.04.2011, 07:21, edited 1 time in total.
mbre
 

Postby koef2 » 10.04.2011, 13:56

Hello,

I write in English, because this is the english part of the Rocrail-Forum.

I think in my opinion it is a little bit strange to write here in the the forum that the TAMS WD-34 circuit controller is on your personal blacklist without any given information about your problems with this controller :D .

I had on my own problems with that controller, too. But forum colleagues have a working WD-34 as you can see, here http://forum.rocrail.net/viewtopic.php?t=2299&highlight=tams+wd34. I know, there is an opendcc setup described and that is different to ddx..

So a few information why it does not work under rocrail in ddx setup in your configuration would be very great.

Best regards and thanks in advance
Kai
Koef2
-------------
Delta 6604, DDX und Rocrail with Linux, Maerklin H0 metal tracks
koef2
 

Postby koef2 » 10.04.2011, 14:03

Hello,

only as add-on to my prior post my problems were here described http://forum.rocrail.net/viewtopic.php?t=1376&highlight=.

The recognition of an adress worked somehow (blinking LED). Due to lightning mistakes of my turnouts I damaged the WD-34 and switched over to Viesmann-Turnout-Decoders, which work very well now. So I had no need to use the WD-34 any longer :D .

So It would be nice to have an information, if this recognition of the adress did work in your trials or not.

Best regards
Kai
Koef2
-------------
Delta 6604, DDX und Rocrail with Linux, Maerklin H0 metal tracks
koef2
 

Re: DDX-Blacklist: Tams WD-34

Postby mbre » 11.04.2011, 10:06

mbre wrote:Der Tams Magnetartikeldekoder WD-34 reagiert überhaupt nicht.


This Decoder is not listed as white or black. So I wrote this warning.
If someone has different experiances, let him write.
"No reaction at all" means
- does not react in command mode (after programming by Multimaus).
- does not react in programming mode.
- does not react in MM and in DCC mode.

So I ordered now a LDT S-4-DC that is listed as OK.
If I have problems also with that one, I know it's my installation.

Of course I searched for a post about this decoder but I did not find the older posts?!? The word Tams is not mentioned in it.
mbre
 

Postby koef2 » 11.04.2011, 15:28

Hello MBRE,

thanks for your explanation.

Best regards
Kai

Koef2
-------------
Delta 6604, DDX und Rocrail with Linux, Maerklin H0 metal tracks
koef2
 

LDT works

Postby mbre » 20.04.2011, 11:30

So I ordered now a LDT S-4-DC that is listed as OK.


That works!
Martin

Roco+LDT HSI88 via RS232
mbre
 


Return to ddx