[Solved] andRoc: make route is set visible for a train

Android Mobile Client

Re: andRoc Improvement: make route is set visible for a trai

Postby rjversluis » 04.01.2015, 16:59

I tested with a Cat Phone B15Q quad core and it shows all changes accurate.
With or without schedule is in this case irrelevant.
Best Regards, Rob.
:!: PS: Do not forget to attach the usual files.
:!: PS: Nicht vergessen die übliche Dateien an zu hängen.
[ macOS - Linux] - [ N: CBus - CAN-GCA ] - [ 0: RocNetNode - GCA-Pi ]
rjversluis
Site Admin
 

Re: andRoc Improvement: make route is set visible for a trai

Postby smitt48 » 04.01.2015, 17:41

Hi Rob,

Cat Phone B15Q quad core


Wow, never knew anybody that had one!

Tom
Kind regards,
Tom Smit
Kralendijk, Bonaire - Dutch Caribbean

Märklin M & K-rails with ECoS2 (4.2.0) - WinXP as server, 10
RoSoft: S88n & WDD switch & SDD signal decoders
Display: Tri-ang from 1950's, Märklin from early 1960's
In build phase
smitt48
 

Re: andRoc Improvement: make route is set visible for a trai

Postby rjversluis » 04.01.2015, 17:59

Hi Tom,
smitt48 wrote:Hi Rob,

Cat Phone B15Q quad core


Wow, never knew anybody that had one!

Tom

That's a phone for men with two SIM cards. ;)
And costs less then an iPhone 4S.
No cover needed; You can throw it on the floor, run over it with your car, IP67, drown it and can be touched in the rain. 8)

http://www.catphones.com/de-de/phones/b15q-smartphone/

Image
Best Regards, Rob.
:!: PS: Do not forget to attach the usual files.
:!: PS: Nicht vergessen die übliche Dateien an zu hängen.
[ macOS - Linux] - [ N: CBus - CAN-GCA ] - [ 0: RocNetNode - GCA-Pi ]
rjversluis
Site Admin
 

Re: andRoc Improvement: make route is set visible for a trai

Postby rvooyen » 04.01.2015, 18:57

So we all need to buy that phone.
Rob has shares in that company :wink:
LOL

Robert
Robert van Ooijen.
Building Rhineland2. 3 levels. CS=IB1-Loconet+HSI-s88, 70 blocks, 160 sensors, 4 boosters. M&K 3rail.
Goal: Scheduled Pass. trains, "OPS" with car cards etc.. Using andRoc and Rocweb/xs throttles.
Rocrail on WinXP.
rvooyen
 

Re: andRoc Improvement: make route is set visible for a trai

Postby rjversluis » 04.01.2015, 19:36

rvooyen wrote:So we all need to buy that phone.

No, but you have to take in account that a bad wifi connection and or a slow android device will decrease the grade of use of it.
Also with my cheep Archos 7" pad I do not see any delays.
Make sure that Rocrail is up to date.
Best Regards, Rob.
:!: PS: Do not forget to attach the usual files.
:!: PS: Nicht vergessen die übliche Dateien an zu hängen.
[ macOS - Linux] - [ N: CBus - CAN-GCA ] - [ 0: RocNetNode - GCA-Pi ]
rjversluis
Site Admin
 

Re: andRoc Improvement: make route is set visible for a trai

Postby rvooyen » 04.01.2015, 19:49

I have a new Galaxy Ace 3 dual core and good wifi.
Not good enough?

Robert
Robert van Ooijen.
Building Rhineland2. 3 levels. CS=IB1-Loconet+HSI-s88, 70 blocks, 160 sensors, 4 boosters. M&K 3rail.
Goal: Scheduled Pass. trains, "OPS" with car cards etc.. Using andRoc and Rocweb/xs throttles.
Rocrail on WinXP.
rvooyen
 

Re: andRoc Improvement: make route is set visible for a trai

Postby smitt48 » 04.01.2015, 19:56

Hi Robert & Rob

Rob has shares in that company :wink:

I have shares in that company! Worked there for 31 years.

Tom
Kind regards,
Tom Smit
Kralendijk, Bonaire - Dutch Caribbean

Märklin M & K-rails with ECoS2 (4.2.0) - WinXP as server, 10
RoSoft: S88n & WDD switch & SDD signal decoders
Display: Tri-ang from 1950's, Märklin from early 1960's
In build phase
smitt48
 

Re: andRoc Improvement: make route is set visible for a trai

Postby agre30 » 05.01.2015, 21:50

Hi Rob,
Everything works fine and normaly the mode in andRoc is up to date.
However, there is one situation when the mode in andRoc is not updated. When a train arrives in a block where it has to stop the speed goes to 0, the mode color turns from green to red and the mode shows 'wait'. Then I touch the speed slider because the train has to move a little forward. Then a route is set while the speed is not 0. The mode in Rocview is set to 'auto', but de mode in andRoc is not updated untill the train reaches the next block where it has to stop.
I don't think this is caused by a slow wifi or android device because it happens only in this specific situation.
I hope you can reproduce this and solve it.

Thanks,

Albert.
Albert,
Märklin 3-rail
Lubuntu 16.04 (server and client) / TamsMC - Booster B-2 / HSI88 / S88N
Stoom / steam / dampf / diesel / E-loc
agre30
 

Re: andRoc Improvement: make route is set visible for a trai

Postby rvooyen » 05.01.2015, 23:11

Rob, Albert,

This is exactly what I see as well.
If train has to stop speed to 0 then thereafter no update occurs until next stop block.

Albert explained it better than i did.

Regards,

Robert
Robert van Ooijen.
Building Rhineland2. 3 levels. CS=IB1-Loconet+HSI-s88, 70 blocks, 160 sensors, 4 boosters. M&K 3rail.
Goal: Scheduled Pass. trains, "OPS" with car cards etc.. Using andRoc and Rocweb/xs throttles.
Rocrail on WinXP.
rvooyen
 

Re: andRoc Improvement: make route is set visible for a trai

Postby rjversluis » 06.01.2015, 14:45

Hi,

I think I have solved it; I will publish this evening.
Best Regards, Rob.
:!: PS: Do not forget to attach the usual files.
:!: PS: Nicht vergessen die übliche Dateien an zu hängen.
[ macOS - Linux] - [ N: CBus - CAN-GCA ] - [ 0: RocNetNode - GCA-Pi ]
rjversluis
Site Admin
 

Re: andRoc Improvement: make route is set visible for a trai

Postby rjversluis » 06.01.2015, 17:48

You can try 473.
Best Regards, Rob.
:!: PS: Do not forget to attach the usual files.
:!: PS: Nicht vergessen die übliche Dateien an zu hängen.
[ macOS - Linux] - [ N: CBus - CAN-GCA ] - [ 0: RocNetNode - GCA-Pi ]
rjversluis
Site Admin
 

Re: andRoc Improvement: make route is set visible for a trai

Postby rvooyen » 06.01.2015, 20:37

Rob,

Tried 473.

Alas, now the status bar is not updating at all, also the speed when changed by the system eg 0 for stop, is not updating on the androc.
I can control the train normally with the androc, but nothing seems to be updated.

PS: Although I have signals this is a very useful feature when going into tunnels, helixes, shadow stations etc where no signals installed.

Regards,

Robert
Robert van Ooijen.
Building Rhineland2. 3 levels. CS=IB1-Loconet+HSI-s88, 70 blocks, 160 sensors, 4 boosters. M&K 3rail.
Goal: Scheduled Pass. trains, "OPS" with car cards etc.. Using andRoc and Rocweb/xs throttles.
Rocrail on WinXP.
rvooyen
 

Re: andRoc Improvement: make route is set visible for a trai

Postby agre30 » 06.01.2015, 22:03

Rob,
Robert is right, it doesn't work anymore. Also the speed slider is not updated when the speed goes to zero.

Albert.
Albert,
Märklin 3-rail
Lubuntu 16.04 (server and client) / TamsMC - Booster B-2 / HSI88 / S88N
Stoom / steam / dampf / diesel / E-loc
agre30
 

Re: andRoc Improvement: make route is set visible for a trai

Postby rjversluis » 06.01.2015, 22:24

Hi,

yes, I test it now also and fixed it in 474.
Best Regards, Rob.
:!: PS: Do not forget to attach the usual files.
:!: PS: Nicht vergessen die übliche Dateien an zu hängen.
[ macOS - Linux] - [ N: CBus - CAN-GCA ] - [ 0: RocNetNode - GCA-Pi ]
rjversluis
Site Admin
 

Re: andRoc Improvement: make route is set visible for a trai

Postby rvooyen » 07.01.2015, 13:13

Result of 474...... FANTASTIC!

Not only is all the updating happening, also the status bar is updated at block ENTER, so allowing the driver to stop the train in time.
The status bar now really works like an in CAB signal - terrific!

I'll let Albert mark the topic as GRANTED (the improvement that is and if agreed by him) since he started this topic.
A future improvement might be a yellow bar if status for second next block is wait. But this is great so far.

:rr_for_ever:

Greetings,

Robert
Robert van Ooijen.
Building Rhineland2. 3 levels. CS=IB1-Loconet+HSI-s88, 70 blocks, 160 sensors, 4 boosters. M&K 3rail.
Goal: Scheduled Pass. trains, "OPS" with car cards etc.. Using andRoc and Rocweb/xs throttles.
Rocrail on WinXP.
rvooyen
 

PreviousNext

Return to andRoc