User Tools

Site Tools


can-gca2-en

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
can-gca2-en [2025/05/15 16:11] – [CAN-GC2 Universal 16 port I/O node for CANBUS] phgcan-gca2-en [2025/06/09 19:11] (current) – [The hardware] phg
Line 1: Line 1:
 ====== CAN-GC2 Universal 16 port I/O node for CANBUS ====== ====== CAN-GC2 Universal 16 port I/O node for CANBUS ======
 [[english|{{  rocrail-logo-35.png}}]] [[english|{{  rocrail-logo-35.png}}]]
-[[:english|Content]] -> [[:hardware-en|Hardware]] -> [[:hardware-en#gca-cbus|CANBUS]]+[[:english|Content]] -> [[:hardware-en|Hardware]] -> [[:hardware-en#gca-cbus|CBUS / RCAN]]
   * [[:cbus:overview-en|CAN-GC Overview]]   * [[:cbus:overview-en|CAN-GC Overview]]
   * [[:can-gca1-en|CAN-GC1]] | [[:can-gca1e-en|CAN-GC1e]] | [[:can-gcln-en|CAN-GCLN]] | **[[:can-gca2-en|CAN-GC2]]** | [[:can-gc3-en|CAN-GC3]] | [[:can-gc4-en|CAN-GC4]] | [[:can-gca5-en|CAN-GC5]] | [[:can-gc6-en|CAN-GC6]] | [[:can-gc7-en|CAN-GC7]] | [[:can-gc8-en|CAN-GC8]]   * [[:can-gca1-en|CAN-GC1]] | [[:can-gca1e-en|CAN-GC1e]] | [[:can-gcln-en|CAN-GCLN]] | **[[:can-gca2-en|CAN-GC2]]** | [[:can-gc3-en|CAN-GC3]] | [[:can-gc4-en|CAN-GC4]] | [[:can-gca5-en|CAN-GC5]] | [[:can-gc6-en|CAN-GC6]] | [[:can-gc7-en|CAN-GC7]] | [[:can-gc8-en|CAN-GC8]]
Line 14: Line 14:
 the CAN-GC2 can be mixed with GCA50 units on the same cable, but of course need different computer interfaces.\\ the CAN-GC2 can be mixed with GCA50 units on the same cable, but of course need different computer interfaces.\\
 The also available CAN-GC3 will bring a complete solution for DCC Model Railroading in DIY. \\ The also available CAN-GC3 will bring a complete solution for DCC Model Railroading in DIY. \\
-The CAN-GC1e connects the computer with the CAN bus. All the well known MGV*/GCA* satellite boards are compatible with the CAN-GC2.  \\+The CAN-GC1e connects the computer with the CAN bus. All the well known MGV*/GCA* satellite boards are useable with the CAN-GC2.  \\
  
  
Line 26: Line 26:
    
  
-A jumper makes it possible to set terminator on the last board in the CANBUS chain.\\ +A jumper makes it possible to set terminator on the last board in the RCAN chain.\\ 
-This jumper connects a 120 Ohm resistor to the CANBUS.\\+This jumper connects a 120 Ohm resistor to the RCAN system.\\
 White connectors at the back are compatible with all [[:mgv-overview-en|GCA(MGV)xx interfaces]].\\ White connectors at the back are compatible with all [[:mgv-overview-en|GCA(MGV)xx interfaces]].\\
 These interfaces are all electrical isolated from CANBUS by optocouplers.\\ These interfaces are all electrical isolated from CANBUS by optocouplers.\\
-Power, as available in CANBUS-cable, is only used for supply of CANBUS board itself.\\+Power, as available in RCAN-cable, is -where ever important- generally only used for supply of RCAN board itself, \\ 
 +with a few minor exceptions.\\
 As a standard recommandation for all CAN systems, connection and disconnection of cables is not possible while system is running.\\ As a standard recommandation for all CAN systems, connection and disconnection of cables is not possible while system is running.\\
 Using this cheap and rigid d-type connector with locking screws will avoid that connectors drop off accidently.\\ Using this cheap and rigid d-type connector with locking screws will avoid that connectors drop off accidently.\\
Line 43: Line 44:
 |  {{:cbus:can-gc2-green-bomfile.pdf|The partslist}}  | |  {{:cbus:can-gc2-green-bomfile.pdf|The partslist}}  |
 |  {{ :gca:can-gc2_stl.zip |  3D print sources for housing}}  | |  {{ :gca:can-gc2_stl.zip |  3D print sources for housing}}  |
 +^  N.B. Only complete ordered kits will be supported!  ^
 \\ \\
-N.B. Only complete ordered kits will be supported! ^+     Housing is only for DIY 3D printing ^ 
 +|  {{ :gca:can-gc2.zip |  Box and cover for CAN-GC2}}  |
 \\ \\
 === Previous version (blue pc-board) === === Previous version (blue pc-board) ===
Line 115: Line 118:
 Read switches and hall sensors can be used as feed-back sensors.\\ Read switches and hall sensors can be used as feed-back sensors.\\
 However, since the contact information inside the CAN-GC2 is arranged so that the unit is\\ However, since the contact information inside the CAN-GC2 is arranged so that the unit is\\
-low sensitive for distorsions, the minimum Pulse lenght to be accepted by CAN-GC2 is 20 miliSeconds (0.02 second).\\+low sensitive for distorsions, the minimum Pulse lenght to be accepted by CAN-GC2 is 50 miliSeconds (0.05 second).\\
 In addition to that, reed-contacts usually give more than 1 pulse when activated, known as 'contact dender'.\\ In addition to that, reed-contacts usually give more than 1 pulse when activated, known as 'contact dender'.\\
 For this way of sensoring, a special pulse-extender is available. See __**[[gca173-en|Hall sensor and reed switch unit]]**__\\ For this way of sensoring, a special pulse-extender is available. See __**[[gca173-en|Hall sensor and reed switch unit]]**__\\
can-gca2-en.1747318289.txt.gz · Last modified: 2025/05/15 16:11 by phg