[closed] Dispatch to Uhli-FRED via gca101 does not work

RocNet(RaspberryPi), mergCBUS and LocoNet based hardware developed by Peter Giling. (GCA)
Documentation: http://wiki.rocrail.net/doku.php?id=english#hardware
Order information: http://wiki.rocrail.net/doku.php?id=gca:gca-index-en/

Re: Dispatch to standalone Uhli-FRED via gca101 does not wor

Postby rjversluis » 16.08.2014, 16:47

Hi Jürgen,

with byte level tracing on you will get everything on the LocoNet.
Best Regards, Rob.
:!: PS: Do not forget to attach the usual files.
:!: PS: Nicht vergessen die übliche Dateien an zu hängen.
[ macOS - Linux] - [ N: CBUS - CANGCx ] - [ G: CBUS - CANGCx ]
rjversluis
Site Admin
 

Re: Dispatch to standalone Uhli-FRED via gca101 does not wor

Postby rjversluis » 16.08.2014, 18:12

I also tested with a serial LocoBuffer, GCA85. Same result.
Best Regards, Rob.
:!: PS: Do not forget to attach the usual files.
:!: PS: Nicht vergessen die übliche Dateien an zu hängen.
[ macOS - Linux] - [ N: CBUS - CANGCx ] - [ G: CBUS - CANGCx ]
rjversluis
Site Admin
 

Re: Dispatch to standalone Uhli-FRED via gca101 does not wor

Postby rjversluis » 17.08.2014, 10:43

Hi,

Peter and I will only support the GCA124, which is FredI compatible, in combination with the GCA101, GCA85 and the Rocrail Slotserver.

I invested at least 4 hours with the old analog Fred from Fremo. (A waist of time...)
The packets coming from the DCS100 and the Slotserver are identical but somehow the old Fred does not understand the Slotserver packets.
Its not a timing issue.

So: No further support from my side.
Best Regards, Rob.
:!: PS: Do not forget to attach the usual files.
:!: PS: Nicht vergessen die übliche Dateien an zu hängen.
[ macOS - Linux] - [ N: CBUS - CANGCx ] - [ G: CBUS - CANGCx ]
rjversluis
Site Admin
 

Re: Dispatch to standalone Uhli-FRED via gca101 does not wor

Postby jriedl » 18.08.2014, 20:18

Thank you Rob,

I've ordered the most recent FREDs from Fremo, arriving in at about 3 weeks. As soon as I have them, I will let you know about the result.
Since Peter writes, he uses the Fremo firmware, it shall work with rocrail in my opinion too.

Best Regards

Jürgen
[K.Bay.Sts.B Epoche 1] [FREMO] [Linux]
jriedl
 

Re: Dispatch to standalone Uhli-FRED via gca101 does not wor

Postby phg » 19.08.2014, 18:30

Hallo Jürgen,


I have my doubts about all these combinations, where Uhlenbrock material is involved.
In the past, there were already some questions on the way Uhlenbrock is using LocoNet.
It seems that they have added and/or changed parts in the protocol, without publishing any documantation about it.
Specially there , you will find no answer, so I do not, since I do not own all these parts, know how to answer on this issue.
Best regards, herzliche Grüße, chaleureuses salutations, saludo cordial, migliori saluti, hjärtliga hälsningar, hartelijke groet,

Peter Giling (Rocrail - LNet(GCAxxx) - Fiddle Yard control GCA145 - CBUS (CAN-GCx)- RocNet (Raspberry Pi GCA-PIxx)
phg
 

Previous

Return to GCA (Hardware by Peter Giling)