(Updated)Clarify Command Station indicators

Post Reply
smitt48
Moderator
Posts: 6076
Joined: 04.04.2014, 01:07
Location: Kralendijk, Bonaire - Dutch Caribbean

(Updated)Clarify Command Station indicators

Post by smitt48 » 19.07.2018, 17:58

Hi Rob (or someone else :mrgreen: ),

I received a question from a user today. I think I know the answer but want to make sure!
Can someone tell me what the entries in the PT and PoM columns indicate?
https://wiki.rocrail.net/doku.php?id=controllers-en
"-" not tested
Y - works
N - does not work
R - only Reading works
W - only Writing works
R/W - Reading and Writing works

Is "Y" the same as R/W

Thanks Tom
Last edited by smitt48 on 21.07.2018, 12:26, edited 2 times in total.

rjversluis
Site Admin
Posts: 42033
Joined: 10.04.2006, 08:48
Location: Speyer, Germany
Contact:

Re: Clarify Command Station indicators

Post by rjversluis » 20.07.2018, 06:33

Hi Tom,
smitt48 wrote:I received a question from a user today. I think I know the answer but want to make sure!
Can someone tell me what the entries in the PT and PoM columns indicate?
https://wiki.rocrail.net/doku.php?id=controllers-en
"-" not tested
Y - works
N - does not work
R - only Reading works
W - only Writing works
R/W - Reading and Writing works

Is "Y" the same as R/W
No, "Y" is the same as W.

smitt48
Moderator
Posts: 6076
Joined: 04.04.2014, 01:07
Location: Kralendijk, Bonaire - Dutch Caribbean

Re: Clarify Command Station indicators

Post by smitt48 » 20.07.2018, 11:00

Hi Rob,

You mind if I change "Y" to "W"?

Thanks Tom

rjversluis
Site Admin
Posts: 42033
Joined: 10.04.2006, 08:48
Location: Speyer, Germany
Contact:

Re: Clarify Command Station indicators

Post by rjversluis » 20.07.2018, 11:05

Hi Tom,
smitt48 wrote:You mind if I change "Y" to "W"?
Its OK 2me.

smitt48
Moderator
Posts: 6076
Joined: 04.04.2014, 01:07
Location: Kralendijk, Bonaire - Dutch Caribbean

Re: Clarify Command Station indicators

Post by smitt48 » 20.07.2018, 12:18

Hi Rob,

The controllers page has been updated. https://wiki.rocrail.net/doku.php?id=controllers-en
Hover over PT and PoM you will see: (Read, Write, No (does not work), ”-” (not tested))

Thanks Tom

RainerK
Moderator
Posts: 4040
Joined: 29.04.2009, 09:31
Location: Sprockhövel (zwischen BO u. W)
Contact:

Re: (Updated)Clarify Command Station indicators(

Post by RainerK » 21.07.2018, 03:32

Hi Rob and Tom,

IMHO there are some missing "R" in the column "PT", especially at CS,
which have a correct working Programming track and send the readed CV values back to Rocrail.

It is definitely in "ddx" and "dccpp" and I did changed the PT entries to "R/W".

smitt48
Moderator
Posts: 6076
Joined: 04.04.2014, 01:07
Location: Kralendijk, Bonaire - Dutch Caribbean

Re: (Updated)Clarify Command Station indicators(

Post by smitt48 » 21.07.2018, 12:10

Hi Rainer,

I saw that too by the CS, but did not want to change it, as I know not much about it.
The question the forum user had was is "Y" = R/W? Rob stated it is not: "Y" = "W"!
So I just documented the codes and changed "Y" to "W", to eliminate one additional code.

Tom

Post Reply

Return to “Wiki”