Pianificazione

Re: Pianificazione

Postby cds » 26.02.2014, 09:39

Buon giorno Michele,

Sorry, up to now I didn't check your schedules, I only checked automatic mode. Obviously you are working with schedules: "20140225.192512.623 r9999I ESU BR 1 OModel 4300 last entry[5] in schedule [st-9-10-11-st] is reached."

*) I've put Gravita in BL-6, direction to the right (anti-orario), and started schedule "st - 11 - 10 - 9 - st" -> Everything is fine, loco stops in Stazione (st) and goes to "idle".
*) I've put Gravita in BL-6, direction to the right (anti-orario), and started schedule "st - 5 - ponte - stnasc" -> Everything is fine, loco stops in Stazione Nascosta (stnasc) and goes to "idle".

I'm not quite sure where your problem is? For me it seems that you would like to run a loco to the left (orario). In automatic mode this is ok and running as I checked yesterday. If you would like to run a loco clockwise (orario) by schedule you have to define a new schedule.

If it doesn't help so far I would like to ask you what
if I planned a route in the orary direction
means for you and which steps you undertook before you got those
Code: Select all
20140225.192512.623 r9999I ESU BR 1 OModel 4369 Try to find a route to block " BL-9".
20140225.192512.623 r9999I ESU BR 1 OModel 4381 route[autogen-[BL-7+]-[BL-9-]] found but it is not in the same direction: reject.
20140225.192512.623 r9999I ESU BR 1 OModel 4300 last entry[5] in schedule [st-9-10-11-st] is reached.
server messages.

Tante grazie!
Beste Grüße/Kind regards
Claus

M* H0 M
HW: TAMS MC, B-2 & B-4, WD-34, VIESSMANN 5211(1), LITTFINSKY & TAMS S88-3
Decoder: Mä & TAMS (MM2)
SW: Win7 64, RR 64, andRoc
cds
 

Re: Pianificazione

Postby michele » 26.02.2014, 19:30

Ciao Claus,

I have cancel the schedules before send you the file, now I have saved again with the schedules that doesn't work (file attached).
In practice I have try a simple tour in clockwise (eg. BL-8 BL-9 BL-10 BL-11 BL-8) and when I start the schedules show the message I told you about; in that specific case I have tried BL-7 BL-9.
From what I understand seem that the route exist "but it is not in the same direction" ???
Claus scusa se continuo a rompere!

Ciao,
Michele
You do not have the required permissions to view the files attached to this post.
michele
 

Re: Pianificazione

Postby cds » 26.02.2014, 20:33

Ciao Michele,

I've loaded your newly attached plan and tested the new schedules.

1) Schedule "8-9-10-11-8": I've put ESU BR151 into block BL-8. Then I've selected "ESU BR151" in the loco control window. Then I've pressed ">>" (or "<<") so that in the column "V__" the info "0>" shows up. (Fyi: This is MY default direction for every loco. It's like a rule for me.) Then I've clicked with the right mouse on block BL-8 and chose "swap placing" and/or "swap block enter side" until
a) the arrow in the block shows to the left,
b) "Block" in the loco control window shows "-BL-8" and
c) "V__" in the loco control window shows "0>".
Finally I've switched on automatic mode and started schedule "8-9-10-11-8" by selecting this schedule at "Start with tour or schedule ...".
The loco runs clockwise the schedule without any problems, stops at BL-8 and goes to mode "idle".

2) Schedule "6-1-2-5-6": I've put "Diesel 6" into block BL-6. The "V__" showed up as "0>" -> ok. Then I've configured the direction of the loco and of the block (the arrow) with "swap placing" and/or "swap block enter side" so, that in column "Block" the info "-BL-6" shows up and in the column "V__" the info "0>" shows up.
Finally I've switched on automatic mode and started schedule "6-1-2-5-6" by selecting this schedule at "Start with tour or schedule ..." and choosing "6-1-2-5-6". The loco runs clockwise the schedule without any problems, stops at BL-6 and goes to mode "idle".

So from my point of view everything is fine with your plan and your schedules. Maybe you will need to practice a little bit with directions of locos and blocks. If you have any further question please don't hesitate to post further.

Lunedi io sono a Trieste per visitare e per fare la spesa :wink:
Beste Grüße/Kind regards
Claus

M* H0 M
HW: TAMS MC, B-2 & B-4, WD-34, VIESSMANN 5211(1), LITTFINSKY & TAMS S88-3
Decoder: Mä & TAMS (MM2)
SW: Win7 64, RR 64, andRoc
cds
 

Re: Pianificazione

Postby paologaletti » 09.12.2014, 07:13

I have understood:
At first flag other in the block.
Then check schedules
Thank you. Bye
paologaletti
 

Previous

Return to Modalità automatica (IT)

cron