Rocweb V2 Preview testing

All about the Rocrail WEB solution.

Re: Rocweb V2 Preview testing

Postby rjversluis » 07.06.2015, 16:25

Hi Tom,

just close FF after it has been connected to the Rocrail server and you get an opcode 3.
Best Regards, Rob.
:!: PS: Do not forget to attach the usual files.
:!: PS: Nicht vergessen die übliche Dateien an zu hängen.
[ macOS - Linux] - [ N: CBus - CAN-GCA ] - [ 0: RocNetNode - GCA-Pi ]
rjversluis
Site Admin
 

Re: Rocweb V2 Preview testing

Postby smitt48 » 07.06.2015, 17:48

Hi Rob,

just close FF after it has been connected to the Rocrail server and you get an opcode 3.


Running 9264.
I don't get an error, I closed 3 different ways.
Used Back arrow, X on Rocweb tab and X on FF screen. Is there another way?
Kind regards,
Tom Smit
Kralendijk, Bonaire - Dutch Caribbean

Märklin M & K-rails with ECoS2 (4.2.3) - Win10
RoSoft: S88n & WDD switch & SDD signal decoders
Display: Tri-ang from 1950's, Märklin from early 1960's
In build phase
smitt48
 

Re: Rocweb V2 Preview testing

Postby rvooyen » 07.06.2015, 18:12

Re Second line in throttle.

OK the WIKI shows some descriptive info for the loc in question.

However in my example the information is for completely different locs. Ie DB 216-068 shows the name of the loc DB 212-245 for some reason.

Re LOC and TRAIN assignment. YES in understand about locs and trains.

It is just a bit confusing if one is starting schedules for a train but the pic of a loc is shown.

In androc this was always loc based.

Robert
Robert van Ooijen.
Building Rhineland2. 3 levels. CS=IB1-Loconet+HSI-s88, 70 blocks, 160 sensors, 4 boosters. M&K 3rail.
Goal: Scheduled Pass. trains, "OPS" with car cards etc.. Using andRoc and Rocweb/xs throttles.
Rocrail on WinXP.
rvooyen
 

Re: Rocweb V2 Preview testing

Postby rjversluis » 07.06.2015, 18:59

Hi Robert,

I think we are talking about different things.

Wiki:
The lines under the loco image are:
1) Loco ID and mode.
2) Loco description.
2/3) Slave locos of the consist. If the selected loco is self a slave, the master will be listed as first. A click on the master ID will select the master loco in the throttle.


See: http://wiki.rocrail.net/doku.php?id=loc-consist-en

Trains are part of the Operator object:
http://wiki.rocrail.net/doku.php?id=operator-consist-en
The cars/wagons composition can be assigned to a loco:
http://wiki.rocrail.net/doku.php?id=loc ... ease_train

So first you must select a loco and then you can assign a train.

This function is not available in any other Rocrail Mobile Client.
Best Regards, Rob.
:!: PS: Do not forget to attach the usual files.
:!: PS: Nicht vergessen die übliche Dateien an zu hängen.
[ macOS - Linux] - [ N: CBus - CAN-GCA ] - [ 0: RocNetNode - GCA-Pi ]
rjversluis
Site Admin
 

Re: Rocweb V2 Preview testing

Postby rvooyen » 07.06.2015, 19:47

OK.

I dont use trains yet so still learning.

Looks like Rocweb getting there now. I will try some more the coming week.

Robert
Robert van Ooijen.
Building Rhineland2. 3 levels. CS=IB1-Loconet+HSI-s88, 70 blocks, 160 sensors, 4 boosters. M&K 3rail.
Goal: Scheduled Pass. trains, "OPS" with car cards etc.. Using andRoc and Rocweb/xs throttles.
Rocrail on WinXP.
rvooyen
 

Re: Rocweb V2 Preview testing

Postby rvooyen » 09.06.2015, 22:18

Using 9270.

Had a great ops session, throttles on android tablets and phone went great, no interruptions!

Now just some fine tuning on the gui re feedback and updating.

MANUAL/AUTO for Loc on throttle.
Issue:
Set loc/train on auto and follow with the throttle. Speeds of course set by RR auto.
So Loc is on say 50kmph as set by auto, if I now want to adjust the speed via the throttle, the throttle remembers IT'S last speed instead of taking what is currently set. So say the last ever set speed on the throttle was 15kph. If I touch one of the up/down buttons, the speed in this case jumps from 50 (auto) to 15 (last manual).
Needed: That any speed mod by throttle should be delta up/down of the current speed, not the last manual speed.

Hope this is clear enough explanation.

Nitpick issue - low priority, re RED setting of turnout/signal when operating trackplan.
If a turnout/signal does not (yet) have an address, and if it is clicked (eg by accident), then the red shows and can never be removed.
Again low priority.

All in all happy with the rocweb function now.

Robert
Robert van Ooijen.
Building Rhineland2. 3 levels. CS=IB1-Loconet+HSI-s88, 70 blocks, 160 sensors, 4 boosters. M&K 3rail.
Goal: Scheduled Pass. trains, "OPS" with car cards etc.. Using andRoc and Rocweb/xs throttles.
Rocrail on WinXP.
rvooyen
 

Re: Rocweb V2 Preview testing

Postby rjversluis » 10.06.2015, 06:08

Hi Robert,

both issues are fixed now.
Best Regards, Rob.
:!: PS: Do not forget to attach the usual files.
:!: PS: Nicht vergessen die übliche Dateien an zu hängen.
[ macOS - Linux] - [ N: CBus - CAN-GCA ] - [ 0: RocNetNode - GCA-Pi ]
rjversluis
Site Admin
 

Re: Rocweb V2 Preview testing

Postby rvooyen » 12.06.2015, 14:51

Feedback on 9305.

There is an issue with the throttle, with speeds jumping around again while operating manually.
Looks like there is crosstalk somewhere, since I has some auto trains in the background. (Old problem reappearing?)

During shunting at slow speeds 5-15kph, all of a sudden 53kph would appear, then 47 and only after hitting the speed buttons many times could I get the speed back to shunting level. Needless to say this made shunting not possible (loc jumping around).

Hope this is enough explanation.

Robert
Robert van Ooijen.
Building Rhineland2. 3 levels. CS=IB1-Loconet+HSI-s88, 70 blocks, 160 sensors, 4 boosters. M&K 3rail.
Goal: Scheduled Pass. trains, "OPS" with car cards etc.. Using andRoc and Rocweb/xs throttles.
Rocrail on WinXP.
rvooyen
 

Re: Rocweb V2 Preview testing

Postby rjversluis » 12.06.2015, 15:03

Hi Robert,

you are right, thats a Rocweb issue...
I will check.
Best Regards, Rob.
:!: PS: Do not forget to attach the usual files.
:!: PS: Nicht vergessen die übliche Dateien an zu hängen.
[ macOS - Linux] - [ N: CBus - CAN-GCA ] - [ 0: RocNetNode - GCA-Pi ]
rjversluis
Site Admin
 

Re: Rocweb V2 Preview testing

Postby rjversluis » 12.06.2015, 15:14

Hi Robert,

I could reproduce and solve the problem.
Best Regards, Rob.
:!: PS: Do not forget to attach the usual files.
:!: PS: Nicht vergessen die übliche Dateien an zu hängen.
[ macOS - Linux] - [ N: CBus - CAN-GCA ] - [ 0: RocNetNode - GCA-Pi ]
rjversluis
Site Admin
 

Re: Rocweb V2 Preview testing

Postby rvooyen » 20.06.2015, 20:47

Fast clock error message when clock called in browser.

Hi.

I am getting this error when the clock is called in rocweb.
20150620.213928.093 r9999E phts030B ODoc 0573 Parser error at position [72]!

Line 730 - 740 in attached trace.

Regards,

Robert
You do not have the required permissions to view the files attached to this post.
Robert van Ooijen.
Building Rhineland2. 3 levels. CS=IB1-Loconet+HSI-s88, 70 blocks, 160 sensors, 4 boosters. M&K 3rail.
Goal: Scheduled Pass. trains, "OPS" with car cards etc.. Using andRoc and Rocweb/xs throttles.
Rocrail on WinXP.
rvooyen
 

Re: Rocweb V2 Preview testing

Postby smitt48 » 20.06.2015, 21:17

Hi Robert,

Try the latest version.

It was fixed,

viewtopic.php?f=72&t=9685&start=15

Tom
Kind regards,
Tom Smit
Kralendijk, Bonaire - Dutch Caribbean

Märklin M & K-rails with ECoS2 (4.2.3) - Win10
RoSoft: S88n & WDD switch & SDD signal decoders
Display: Tri-ang from 1950's, Märklin from early 1960's
In build phase
smitt48
 

Previous

Return to Rocweb