6051 Interface and USB/Serial converter WIN7

Post Reply
DRich

6051 Interface and USB/Serial converter WIN7

Post by DRich » 18.01.2012, 19:58

Hi,
I'm novice on rocrail and try to control train with following config: 6051, USB/Serial converter Digitus DA 70156 Win7/64. Changing direction forward/back is not woking properly. Connect serial port diect on older PC Win7/32 everything running fine. Tried to change USB/Serial parameters without success. Maybe someone has experience.
Dietger
Attachments
rocrail.ini
(1.67 KiB) Downloaded 283 times
plan.xml
(25.69 KiB) Downloaded 289 times

rjversluis
Site Admin
Posts: 41680
Joined: 10.04.2006, 08:48
Location: Speyer, Germany
Contact:

Post by rjversluis » 19.01.2012, 11:36

Hi Dietger,

if you supply two traces, one from the working old pc and one with the new.
In both traces the change direction should be visible so they can be compared.

DRich

6051 Interface and USB/Serial converter WIN7

Post by DRich » 19.01.2012, 21:28

Hi Rob, sounds you are very close (Südpfalz). Well here are the files where it's working fine while RS232 is connected direct on serial port. I assume it related to the USB/RS232 and the speed even if Baud Rate (2400) and CTS are same. BTW loco lights on/off is working fine in both cases.
Thanks Dietger
Attachments
plan.xml
(6.77 KiB) Downloaded 279 times
rocview.ini
(1.38 KiB) Downloaded 264 times

DRich

6051 Interface and USB/Serial converter WIN7

Post by DRich » 28.01.2012, 22:21

Hi,
did you get any idea on my question? Did it work with my files?
Thanks
Dietger

rjversluis
Site Admin
Posts: 41680
Joined: 10.04.2006, 08:48
Location: Speyer, Germany
Contact:

Post by rjversluis » 29.01.2012, 08:19

Hi Dietger,

you did not send the trace files.

DRich

6051 Interface and USB/Serial converter WIN7

Post by DRich » 29.01.2012, 10:39

Hi Rob,
maybe I don't know what the trace file is. I send the *.ini and *.xlm from old PC. Which other file is availble and where can I get it?
thanks Dietger

73funki
Posts: 728
Joined: 02.05.2009, 15:44
Location: near Dresden

Post by 73funki » 29.01.2012, 15:53

Hallo Dieter!

Tracefiles are the files in the rocrail directory ending in .trc.

Normally you delete all your trace-files, make your test and send the new trc-files.

DRich

Post subject: 6051 Interface and USB/Serial converter WIN7

Post by DRich » 15.02.2012, 18:52

Hi,
finalliy after business trip I had time to work on the program again.
here are the files hope to get some help.
Dietger

DRich

Post subject: 6051 Interface and USB/Serial converter WIN7

Post by DRich » 15.02.2012, 18:57

Hi,
just realized the system doesn't allow to transfer files with .trc extension.
What to do?
thanks

Besra
Moderator
Posts: 3753
Joined: 10.08.2009, 17:54
Location: North Rhine-Westphalia, Germany

Post by Besra » 15.02.2012, 19:33

Hi Dietger,

just ZIP them: Open Explorer, mark all relevant files and select "Send to... ZIP compressed folder" from the context menu.

Best regards
Besra

M_C_nl
Posts: 337
Joined: 11.09.2010, 23:16
Location: Aachen/Germany

Post by M_C_nl » 15.02.2012, 19:35

Hi Dieter,

best thing to do is to zip the files. If you have problems with zipping, just rename the extension .trc to .trc_txt or something else. then you should be able to send the files.

Regards,
Maxel :-)

DRich

6051 Interface and USB/Serial converter WIN7

Post by DRich » 15.02.2012, 19:58

Hi all,
thanks for the help. here are the here are the files.
Dietger
Attachments
rocview.000.trc.zip
Tracefiles on old PC interface connected direct to RS232 and it always works
(4.74 KiB) Downloaded 234 times
rocview.002.trc.zip
Tracefiles on old PC interface connected with USB_RS232 converter and it works sometime
(4.22 KiB) Downloaded 254 times
rocrail.007.trc.zip
Files on new PC with USB_RS232 and it doesn't work
(8.36 KiB) Downloaded 239 times

Post Reply

Return to “P50 and P50x”